QuiK-Spec® 和 QuiK-Lab® - 即时分析的关键环节
为生产出磷含量更低、二氧化碳排放量更少的优质钢材，炼钢厂必须重新设计转炉工艺。关键在于在此过程中更快地了解钢成分。
贺利氏电测骑士的 QuiK-Lab® 光谱分析装置可在转炉处理过程中，在浸没取样后一分钟内对碳、磷、锰和硫等最关键元素进行快速可靠的分析。
- 在吹炼结束前，提供有关钢水成分的所有重要信息。
- 帮助操作员决定采取哪些措施使温度、碳、磷符合规格要求。
- 最大限度地减少补吹和过吹。
- 将转炉出钢间隔时间缩短几分钟，提高转炉车间的生产率。
提供清洁的无制剂样品
- 由于使用了气体吹扫技术，无论是氮气还是氩气
- 独特的样品设计
- 灵活自主地选择正确的探头类型
- 新硬件可使用 TSC-TSO 探头和 QuiK-Spec® 探头进行测量
副枪技术与新型 Multi-Lance® QuiK-Spec® 一起使用，可提供与现有 Multi-Lance® 传感器相同的温度、氧气和液相线测量功能。
QuiK-Lab® 3
|
Item |
Description |
|---|---|
| Measurement application | Element composition (C, Mn, S, P, Al, V, Cr, Si, Mo, Ni, Co, Cu, Nb, Ti, Sn, As, Ca, B, Mg, Zr) of QuiK-Spec® samples (QSS) |
| Analysis time | 85 sec with 2 sparks |
| Display resolution | 0.0001 |
| Display units | wt%, ppm, pts |
| Voltage/Frequency | 1 Ph 100-240VAC 50/60Hz; Power (operational, peak): unknown; Power (operational, heating): <640W@230 V, <320W@110 V; Currency (operational): < 10A@230, < 16 A @110 Volt ; Short circuit current rating: < 20 kVA |
| Fuse | Slow blow fuse |
| Argon | 6,8 bar max; lab quality (min 5.0); consumption 2 l/min between measurements and <5,8SL/min during measurements. |
| Ambiant operating temperature | -20 ºC to 50 ºC (-4 °F to 122 °F) 1 |
| Operating humidity range | between 5% and 90% (at 20ºC or 68°F) 2 |
| Storage conditions | between -20°C and 70°C (-4 °F and 158 °F) with a maximum of 90% non condensing RH |
| Dimensions | 850 x 750x 1830 mm (length, width, height) |
| Weight | 620 kg |
1 To ensure optimal performance at cold temperatures we have mounted on the internal heatsink four 160W PTC heaters (HP06-2/15-240) (together 160W at 230V, 146W at 110V) per heater. The heaters will heat up the cabinet and electronics until the temperature is high enough to start the IPC and the .NET script safely. During this pre-heating the pre-heating light will light up.
2 In high humidity conditions small amounts of condensation can be formed on the internal heatsink. Underneath this heatsink there is a drain reservoir and flexible tubing to lead water to the outside of the cabinet
QuiK-Lab® 3
|
Item |
Description |
|---|---|
| Measurement application | Element composition (C, Mn, S, P, Al, V, Cr, Si, Mo, Ni, Co, Cu, Nb, Ti, Sn, As, Ca, B, Mg, Zr) of QuiK-Spec® samples (QSS) |
| Analysis time | 85 sec with 2 sparks |
| Display resolution | 0.0001 |
| Display units | wt%, ppm, pts |
| Voltage/Frequency | 1 Ph 100-240VAC 50/60Hz; Power (operational, peak): unknown; Power (operational, heating): <640W@230 V, <320W@110 V; Currency (operational): < 10A@230, < 16 A @110 Volt ; Short circuit current rating: < 20 kVA |
| Fuse | Slow blow fuse |
| Argon | 6,8 bar max; lab quality (min 5.0); consumption 2 l/min between measurements and <5,8SL/min during measurements. |
| Ambiant operating temperature | -20 ºC to 50 ºC (-4 °F to 122 °F) 1 |
| Operating humidity range | between 5% and 90% (at 20ºC or 68°F) 2 |
| Storage conditions | between -20°C and 70°C (-4 °F and 158 °F) with a maximum of 90% non condensing RH |
| Dimensions | 850 x 750x 1830 mm (length, width, height) |
| Weight | 620 kg |
1 To ensure optimal performance at cold temperatures we have mounted on the internal heatsink four 160W PTC heaters (HP06-2/15-240) (together 160W at 230V, 146W at 110V) per heater. The heaters will heat up the cabinet and electronics until the temperature is high enough to start the IPC and the .NET script safely. During this pre-heating the pre-heating light will light up.
2 In high humidity conditions small amounts of condensation can be formed on the internal heatsink. Underneath this heatsink there is a drain reservoir and flexible tubing to lead water to the outside of the cabinet